Description: Snow Performance 210 Stage 2 Boost Cooler Water Methanol Injection Kit Part Number SNO-210Unlock 50-70 HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2.5 Boost Cooler™ water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged). The Stage 2.5 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less water methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives a accurate delivery of water methanol and allows cooling and performance improvements over a wide range for improved drivability. Especially helpful for direct injected engines to remove 100% of carbon build up on the valves. Recommended for all street/strip driven forced induction vehicles using a turbo or centrifugal supercharger (Procharger/Vortech) looking for cooling over a wide range. Unlock 50-70 HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2.5 Boost Cooler water-methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged). The Stage 2.5 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less water-methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Especially helpful for direct-injected engines to remove 100% of carbon build-up on the valves. Recommended for all street/strip driven forced induction vehicles using a turbo or centrifugal supercharger (Procharger/Vortech) looking for cooling over a wide range. The VC-50 (ISO 9001 Manufactured) controller offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a bright 7-color (Blue, White, Red, Yellow, Orange, Purple, Green) O-LED screen displaying boost, percentage of injection, low level, secondary stage activation, prime button, and system fault codes directly on the screen. You can tailor the controller color to match your OEM gauges or mix and match up to two colors! This kit utilizes the only OEM-approved water-methanol injection pump on the market with a proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment 300 PSI UHO pump is designed to be in the elements with O-Ring connections that are then sealed and potted to ensure no moisture can enter the pump internals. Compare this to pumps that use a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat greatly decreasing pump life. The Stage 2.5 comes standard with 100% methanol-resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL compression fittings for guaranteed leak-free operation even when using 100% methanol. Whether running a supercharger, turbo, or high compression motor the Stage 2.5 Boost Cooler will make the induction charge colder, denser, and increase 91 octane fuel to 116 octane race gas levels allowing full power all the time! NOT FOR TRUNK MOUNTING, SOLENOID(SNO-40060) AND LONGER FEEDLINE IS NEEDED IF MOUNTING IN THE TRUNK Features: U.S.A. MadeAdjustable Progressive Water Methanol Engagement & MonitoringDigital Boost Reading (1-50 PSI)Recommended For Street Driven Turbo and Centrifugal Supercharger ApplicationsSupports 1,000+ HP100% Methanol Resistant (Stainless Steel, Nickel Plating, Hard Anodizing, EPDM)Snow Performance Hyper-Sonic Water Methanol NozzleSnow Performance ACU-SEAL Water Methanol Compression FittingsSnow Performance OEM Approved Extreme Environment 300 PSI UHO Water Methanol PumpSnow Performance Running "S" Engraved Low Profile Nozzle HolderSnow Performance Running "S" Engraved Low Profile High Flow Check Valve Free shipping to the lower 48 states. If you are outside of this area please select a calculated shipping method or contact us for a discounted shipping quote.
Price: 583.34 USD
Location: Cypress, California
End Time: 2023-09-02T20:13:29.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Performance Part: Yes
Country/Region of Manufacture: United States
Material: Multiple
California Prop 65 Warning: This item is found to have compounds and chemicals known to the State of California to cause cancer, birth defects, and reproductive harm
Mounting Hardware Included: Yes
Type: Water/Meth Injection
Manufacturer Part Number: SNO-210
Universal Fitment: Yes
Brand: Snow Performance
Manufacturer Warranty: 1 Year
